The 40BD is an IEC 61094 WS3P ¼" prepolarized pressure microphone with rear-venting. Read about the externally polarized equivalent [40BP]
It is a high-precision Type 1 condenser microphone made according to IEC 61094-4 requirements. Its low sensitivity makes it ideal for sound measurements at high frequencies and high sound pressure levels of up to 174 dB. Its small size reduces the effects of diffraction and reflections around the microphone, resulting in a frequency range that extends up to 70 kHz.
40BD is individually factory-calibrated and delivered with a calibration chart stating its specific open-circuit sensitivity and pressure frequency response.
Typical applications and use
The 40BD is ideal for sound pressure measurements, as well as high frequency and high level pressure measurements. It is suitable for general purpose acoustic measurements in couplers and at boundaries. 40BD is included in the G.R.A.S. 46BD ¼" Pressure microphone set.
The 40BD requires a standardized ½" or ¼" CCP preamplifier and an input module that supports this technology with a BNC, SMB, or Microdot connector.
For more information, see System Setup.
For daily verification and check of your measurement setup, we recommend using a calibrator like G.R.A.S. Sound Level Calibrator 42AB.
For proper sensitivity calibration, we recommend using a pistonphone like G.R.A.S. Intelligent Pistonphone 42AP.
Quality and warranty
All G.R.A.S. microphones are made of high-quality materials that will ensure life-long stability and robustness. The microphones are all assembled in verified clean-room environments by skilled and dedicated operators with many years of expertise in this field.
The microphone diaphragm, body, and improved protection grid are made of high-grade stainless steel, which makes the microphone resistant to physical damage, as well as corrosion caused by aggressive air or gasses.
This, combined with the reinforced gold-plated microphone terminal which guarantees a highly reliable connection, enables G.R.A.S. to offer 5 years warranty against defective materials and workmanship.
Learn more about G.R.A.S.' unique warranty policies.
If you accidentally damage the diaphragm on a G.R.A.S. microphone, we can—in most cases—replace it at a very reasonable cost and with a short turn-around time. This not only protects your investment, but also pleases your quality assurance department because you don't have to worry about new serial numbers, etc.
Learn more about G.R.A.S.' service program.
Before leaving the factory, all G.R.A.S. microphones are calibrated in a controlled laboratory environment using traceable calibration equipment.
Depending on the use, measurement environment, and internal quality control programs, we recommend recalibrating the microphone at least once a year.
Learn more about G.R.A.S.' calibration services.
|Frequency range (±1 dB)||Hz||10 to 25 k|
|Frequency range (±2 dB)||Hz||4 to 70 k|
|Dynamic range lower limit (microphone thermal noise)||dB(A)||34|
|Dynamic range lower limit with G.R.A.S. preamplifier||dB(A)||44|
|Dynamic range upper limit||dB||170|
|Dynamic range upper limit with G.R.A.S. CCP preamplifier||dB||164|
|Open-circuit sensitivity @ 250 Hz (±3 dB)||mV/Pa||1.6|
|Open-circuit sensitivity @ 250 Hz (±3 dB)||dB re 1V/Pa||-56|
|Microphone cartridge capacity, typical||pF||7|
|IEC 61094 designation||TBD|
|Temperature range, operation||°C / °F||-40 to 120 / -40 to 248|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Temperature coefficient @250 Hz||dB/°C / dB/°F||-0.01 / -0.006|
|Static pressure coefficient @250 Hz||dB/kPa||-0.008|
|Humidity range non condensing||% RH||0 to 100|
|Humidity coefficient @250 Hz||dB/% RH||-0.001|
|Influence of axial vibration @1 m/s²||dB re 20 µPa||55|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||1.5 / 0.053|
Typical frequency response (without protection grid)