Typical applications and use
The broad working range and reliability has made 40AO the preferred prepolarized microphone for coupler and ear simulator setups and is the natural supplement or replacement of existing solutions. The 40AO is especially suited for audiometer calibration when using a sound level meter / analyzer without a 200 V polarization feature.
It is used for production line testing in coupler setups for test of hearing aids, earphones, headphones, and headsets.
The KEMAR Manikin can also be configured with 40AO for wide-band binaural sound quality recordings.
40AO can be used in
- G.R.A.S. IEC 60318-1 Ear Simulator RA0039
- G.R.A.S. IEC 60318-5 2cc Coupler RA0038 (incl. protection grid)
- G.R.A.S. KEMAR Manikin 45BA
40AO is included in
- G.R.A.S. IEC 60318-4 (60711) Ear Simulator RA0045-S1
- G.R.A.S. IEC 60318-1 & -2 Ear Simulator System Type 43AA-S2
Other coupler systems can be configured with the 40AO and a CCP preamplifier on request.
The 40AO is a very versatile microphone when connected to the RA0067 Transmitter Adapter for ½" Microphones. The 40AO becomes a high-impedance sound source when the RA0067 takes a calibration signal directly from the signal generator and makes the microphone behave like an electrostatic loudspeaker. In a coupler, this gives a frequency response that is as good as when the 40AO behaves like a microphone.
The 40AO requires a standardized ½" or ¼" CCP preamplifier and an input module that supports this technology with a BNC, SMB, or Microdot connector.
For more information, see System Setup.
For daily verification and check of your measurement setup, we recommend using a calibrator like G.R.A.S. Sound Level Calibrator 42AB.
For proper sensitivity calibration, we recommend using a pistonphone like G.R.A.S. Intelligent Pistonphone 42AP.
Quality and warranty
All G.R.A.S. microphones are made of high-quality materials that will ensure life-long stability and robustness. The microphones are all assembled in verified clean-room environments by skilled and dedicated operators with many years of expertise in this field.
The microphone diaphragm, body, and improved protection grid are made of high-grade stainless steel, which makes the microphone resistant to physical damage, as well as corrosion caused by aggressive air or gasses.
This, combined with the reinforced gold-plated microphone terminal which guarantees a highly reliable connection, enables G.R.A.S. to offer 5 years warranty against defective materials and workmanship.
Learn more about G.R.A.S.' unique warranty policies.
If you accidentally damage the diaphragm on a G.R.A.S. microphone, we can—in most cases—replace it at a very reasonable cost and with a short turn-around time. This not only protects your investment, but also pleases your quality assurance department because you don't have to worry about new serial numbers, etc.
Learn more about G.R.A.S.' service program.
Before leaving the factory, all G.R.A.S. microphones are calibrated in a controlled laboratory environment using traceable calibration equipment.
Depending on the use, measurement environment, and internal quality control programs, we recommend recalibrating the microphone at least once a year.
Learn more about G.R.A.S.' calibration services.
|Frequency range (±1 dB)||Hz||5 to 12.5 k|
|Frequency range (±2 dB)||Hz||3.15 to 20 k|
|Dynamic range lower limit (microphone thermal noise)||dB(A)||20|
|Dynamic range lower limit with G.R.A.S. preamplifier||dB(A)||25|
|Dynamic range upper limit||dB||154|
|Dynamic range upper limit with G.R.A.S. CCP preamplifier||dB||146|
|Open-circuit sensitivity @ 250 Hz (±3 dB)||mV/Pa||12.5|
|Open-circuit sensitivity @ 250 Hz (±3 dB)||dB re 1V/Pa||-38|
|Microphone cartridge capacity, typical||pF||20|
|IEC 61094 designation||TBD|
|Temperature range, operation||°C / °F||-40 to 120 / -40 to 248|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Temperature coefficient @250 Hz||dB/°C / dB/°F||-0.02 / -0.007|
|Static pressure coefficient @250 Hz||dB/kPa||-0.007|
|Humidity range non condensing||% RH||0 to 100|
|Humidity coefficient @250 Hz||dB/% RH||-0.001|
|Influence of axial vibration @1 m/s²||dB re 20 µPa||66|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||6.5 / 0.229|
Typical frequency response.