G.R.A.S. 46DP 1/8" LEMO Pressure Microphone Set with Integrated Cable

Freq range: 6.5 Hz to 140 kHz
Dyn range: 46 dB(A) to 191 dB
Sensitivity: 0.7 mV/Pa

Introduction

Through a close cooperation with our customers, we know that data-safety is highly important because the costs related to unsuited and unreliable sensors may determine whether your project turns into a success or not.

For our users, data safety translates directly into requests for easier microphone selection, simple system configuration and reduction of measurement errors.

To meet these requirements, we invented the microphone set concept. It is simple, reliable and robust and consists of a microphone cartridge and preamplifier combination, which is calibrated as one unit. This eliminates errors because there is only one sensitivity value to account for and the risk of contaminating the interface is eliminated. Combine this with our unique and proven design and you have the most reliable measurement microphone sets available in the industry today.

Typical application and use

The 46DP is a pressure microphone set and as such optimized for acoustic measurements of the sound source in a closed coupler or the measurement of sound pressure at a boundary or wall; in which case the microphone forms part of the wall and measures the sound pressure on the wall itself

The high cut-off frequency makes it ideal for ultra-sonic diagnostics and impulse measurements, where minimum distortion and high resolution are obtained by the small size and fast response of the diaphragm.

Regarding temperature range, see the Specifications. Should higher temperature limits be required, we recommend considering  the G.R.A.S. probe microphones where the microphone and preamplifier can be isolated from the hot source.

Design

The G.R.A.S. 46DP is a high-performance  standard microphone set. In our clean-room environment the set is assembled and sealed with a label. However, the microphone set can be dismounted, if  you wish to use the components separately.

Microphone
The microphone cartridge is the high-quality G.R.A.S. 40DP 1/8" Ext. Polarized Pressure Microphone designed for long-term reliability in multiple environments.

Preamplifier
The preamplifier is the G.R.A.S. 26TC 1/4" Preamplifier with TEDS, and based on our well-known circuit board substrates. In the industry these are famous for their low self-noise, wide frequency and excellent slew rate performance.

Compatibility

To perform as specified, the G.R.A.S. 46DP microphone set requires a power module or an analyzer input which can supply the preamplifier with power as well as 200 V polarization. If the power supply is lower, the capability of driving long cables is reduced and consequently the upper frequency is reduced. If the voltage supply is lower it will influence the upper dynamic range.

The microphone set is terminated with a LEMO 7-pin connector. Ready to used  cable assemblies  with LEMO connectors of various types and lengths are available in standard as well as customized lengths.

The 46DP is IEEE 1451.4 TEDS 27v. 1.0 compliant. If your measurement platform supports Transducer Electronic Data Sheets you will be able to read and write data like properties and calibration data.

Alternatives

The G.R.A.S. 46DP-1 use the same microphone cartridge (G.R.A.S. 40DP) but  is provided with the G.R.A.S. 26AC-1 preamplifier. This is provided with an integrated 5-pin mini-LEMO connector.

System verification

The functionality of TEDS is very useful to determine which microphone is connected to which input channel. However, it is not a check of whether the microphone is within specifications or not. For daily verification and check of your measurement setup, we therefore recommend using a sound source like the G.R.A.S. 42AB Sound Calibrator.

For proper sensitivity calibration we recommend using a reference sound source like the G.R.A.S. 42AP Intelligent Pistonphone.

Service

Should you by mistake damage the diaphragm on a G.R.A.S. microphone we will in most cases be able to exchange it at a very reasonable cost and short turn-around time. This not only protects your investment but also meets your quality assurance department since you do not have to worry about new serial numbers etc.

Calibration

When leaving the factory, all G.R.A.S. microphones have been calibrated in a controlled laboratory environment using traceable calibration equipment. Depending on the use, measurement environment and internal quality control programs we recommend that the microphone is recalibrated at least once a year.

Quality and warranty

G.R.A.S. microphone sets are made of components from our proven standard portfolio and are all manufactured of high-quality material and branded parts that were chosen and processed to ensure life-long stability and robustness.

All parts are manufactured and assembled at the factory in Denmark by skilled and dedicated operators in a verified clean-room environment. The microphone diaphragm, body and unique protection grid are made of high-grade stainless steel and make the microphone set resistant to physical damage as well as corrosion caused by aggressive air or gasses.

This, together with the enforced gold-plated microphone terminal guarantees a highly reliable connection. Thanks to the high quality, our warranty against defective materials and workmanship is 5 years.

Frequency range (±1 dB) Hz 10 to 25 k
Frequency range (±2 dB) Hz 6.5 to 140 k
Dynamic range lower limit with G.R.A.S. preamplifier dB(A) 46
Dynamic range upper limit with G.R.A.S. preamplifier @ +28 V / ±14 V power supply dB 179
Dynamic range upper limit with G.R.A.S. preamplifier @ +120 V / ±60 V power supply dB 191
Set sensitivity @ 250 Hz (±4 dB) mV/Pa 0.7
Set sensitivity @ 250 Hz (±4 dB) dB re 1V/Pa -63
Output impedance Ω 75
Power supply min. to max. (single/balanced) V 28 to 120 / ± 14 to ± 60
DC-offset, min., single suppy V 0.5 x Vs - 1
DC-offset, max., single suppy V 0.5 x Vs + 4
DC-offset, balanced supply V -1 to 4
Microphone venting Rear
Temperature range, operation °C / °F -30 to 70 / -22 to 158
Temperature range, storage °C / °F -40 to 85 / -40 to 185
Temperature coefficient @250 Hz dB/°C / dB/°F -0.01 / -0.006
Static pressure coefficient @250 Hz dB/kPa -0.008
Humidity range non condensing % RH 0 to 100
Humidity coefficient @250 Hz dB/% RH -0.0013
Influence of axial vibration @1 m/s² dB re 20 µPa 55
TEDS UTID (IEEE 1451.4) 27 v. 1.0
Connector type 3 m 7-pin LEMO
CE/RoHS compliant/WEEE registered Yes / Yes/Yes
Weight g / oz 7 / 0.247

Typical frequency response (without protection grid).

Optional items

G.R.A.S. AA0009

10 m LEMO 7-pin - LEMO 7-pin Cable

G.R.A.S. AA0020-CL

Customized Length LEMO 7-pin - LEMO 7-pin Cable

G.R.A.S. AL0029

1/4" Microphone Holder, POM

G.R.A.S. AL0013

1/4" Microphone Holder, Stainless Steel

G.R.A.S. AL0005

Swivel head

G.R.A.S. AL0006

Tripod

G.R.A.S. RA0173

1/8” Nosecone

G.R.A.S. AM0071

Windscreen for 1/4" Microphones

G.R.A.S. 12AA

2-Channel Power Module with gain, filters and SysCheck generator

G.R.A.S. 12AK

1-Channel Power Module with gain, filters and SysCheck generator

G.R.A.S. 12AQ

2-Channel Universal Power Module with signal conditioning and PC interface

G.R.A.S. 42AB

Sound Calibrator, Class 1

G.R.A.S. 42AP

Intelligent Pistonphone, Class 0