G.R.A.S. 43BA-2 1/4" 0.4cc CCP High Frequency Coupler Kit

Connection: 0 V/CCP
Volume: 0.4cc
Dyn range: 44 dB(A) to 166 dB
  • 43BA-2 1/4
  • 43BA-2 1/4
  • 43BA-2 1/4
  • 43BA-2 1/4

Introduction
The G.R.A.S. 43BA-2 is a high frequency 1/4" 0.4cc coupler kit for test of hearing aids at frequencies up to 16 kHz. It is a complete kit with a 1/4" Pressure Microphone and a 1/4" Preamplifier with BNC connection and the same adapters known from the reference 2cc coupler. It is easy and safe to handle and calibrate because the microphone grid does not have to be removed for mounting or calibration.

Typical applications and use
It is designed to facilitate the measurement needs described in the IEC 60118 Technical Specification "Electroacoustics - Hearing Aids - Measurement of the performance characteristics of hearing aids" (2013) and meet the need for an accurate and repeatable measurement method that can be used by designers of hearing aids and hearing aids receivers, and by fitters of hearing aids.

The small volume in combination with the 1/4" microphone results in a wide frequency range that makes it useful for high-frequency diagnostics. The extended frequency range also ensures that it is a future proof choice for high-frequency testing of wide-band hearing aids.

Its 0.4cc volume is a well defined cylinder where the diaphragm of the microphone is flush with the bottom of the cylinder. The cylinder is machined to within ±2% of the nominal 0.4cc volume. The exact volume for each individual coupler is stated in the accompanying calibration chart. The performance of the 0.4cc coupler can therefore be accurately simulated, and it can easily be a part of a complete simulation model.

The 43BA is designed for repetitive use and is equally suited for research, quality assurance and production test applications.

Design
The 43BA is developed with and for the hearing aids industry. Through our close collaboration with global leaders within the industry, we found an increasing need for test of modern hearing aids at high frequencies. In accordance with the intentions of the previously mentioned IEC Technical Specification GRAS has designed a coupler kit capable of delivering differentiated and reproducible data up to 16 kHz.  

Because of the small volume, the measured sound level from the 0.4cc coupler is 13.5 dB higher than with a 2cc coupler. This increase in level improves the signal-to-noise ratio compared to what is normally achievable with the 1/4" microphone used.

Another benefit of the small volume and the 1/4" microphone is the fact that the resonance frequency at 30 kHz is so high that it does not interfere with measurements in the audible frequency range. Therefore it can be used for measurements up to 16 kHz, one octave higher than achievable with the standardized 2cc coupler.

The 43BA-2 is designed to perform optimally with the G.R.A.S. 40BD Prepolarized Pressure Microphone, which is ideally suited for for sound measurements at high levels and high frequencies. It has a wide dynamic range for measuring sound pressure levels up to 168 dB. The preamplifier is the  G.R.A.S. 26CS CCP Standard Preamplifier, Very Short. The 26CS is a small robust unit short enough for use in confined spaces like anechoic test chambers. It has a very low inherent-noise level, a wide dynamic range and a frequency response from below 2 Hz to above 200 kHz.

The microphone set is locked and kept firmly in position by a very precise locking mechanism, that automatically centers and  locks the microphone at the same time, eliminating the risk of measurement errors caused by incorrect positioning of the microphone. An O-ring ensures a tight sealing of the microphone. The microphone set can easily be removed for sensitivity calibration – without tools. There is never any need for removing the protective grid, neither for use, calibration or other handling of the microphone.

Compatibility
The G.R.A.S. 43BA-2 requires a power module or measurement  instrumentation input that that can provide a constant current of app. 4 mA. The microphone set requires a Microdot-BNC cable that is part of the delivery. Various extension cables are available. The 0.4cc coupler housing fits all G.R.A.S. 1/2" 2cc standard ear mould and tube adapters.

System verification
For daily verification and check of your measurement setup we therefore recommend using a sound source like the G.R.A.S. 42AB Sound Calibrator. For proper sensitivity calibration we recommend using a reference sound source like the G.R.A.S. 42AP Intelligent Pistonphone.

Performance and warranty
G.R.A.S. microphone sets and couplers are all manufactured of high-quality materials and brand parts that were chosen and processed to ensure life-long stability and robustness.

All parts are manufactured and assembled at the factory in Denmark by skilled and dedicated operators in verified clean-room environments. The microphone diaphragm, body and unique protection grid are made of high-grade stainless steel and make the microphone set resistant to physical damage as well as corrosion caused by aggressive air or gasses.

This, together with the reinforced gold plated microphone terminal which guarantees a highly reliable connection, enables us to offer 5 years warranty against defective materials and workmanship.

The warranty for cables is 6 months.

Theoretical dynamic range lower limit with G.R.A.S. preamplifier dB(A) 44
Theoretical dynamic range upper limit with G.R.A.S. preamplifier @ +28 V / ±14 V power supply dB 166
Set sensitivity @ 250 Hz (±3 dB) mV/Pa 1.45
Set sensitivity @ 250 Hz (±3 dB) dB re 1V/Pa -57
Coupler volume 0.4 ccm
Resonance frequency kHz 30
Temperature range, operation °C / °F -30 to 60 / -22 to 140
Temperature coefficient @250 Hz dB/°C / dB/°F -0.01
Humidity range non condensing % RH 0 to 80
CE/RoHS compliant/WEEE registered Yes/Yes/Yes
Connector type Microdot 10/32
Weight g / oz 50 / 1.76

 

Included

G.R.A.S. RA0252 0.4cc Coupler
G.R.A.S. 40BD ¼" Prepolarized Pressure Microphone, High levels   
G.R.A.S. 26CS ¼" CCP Preamplifier with Microdot Connector,  Very Short
G.R.A.S. AA0070 3 m Cable Microdot-BNC
G.R.A.S. RA0270 Ear-mould Adapter Kit for RA0038 / RA0252 Couplers
G.R.A.S. RA0271 Tube Adapter for RA0038 / RA0252
G.R.A.S. RA0272 IIn-Ear Adapter for RA0038  / RA0252 Couplers

 

Optional

G.R.A.S. AA0035  3-m BNC extension cable
 G.R.A.S. AG0002 CCP Input Adapter
G.R.A.S. 12AL 1-Channel CCP Power Module with A-weighting Filter
G.R.A.S. 12AQ 2-Channel CCP/LEMO Power Module with Signal Conditioning and Computer Interface
G.R.A.S. 42AP Intelligent pistonphone
G.R.A.S. 42AB Sound Calibrator