Typical Applications and use
General-purpose preamplifi er
In-situ check of complete measurement chains
All G.R.A.S. microphone preamplifiers are based on a small ceramic thick-film substrate with a very high input impedance. The ceramic substrate is shielded by a guard ring to minimise the influence of stray capacitance and microphonic interference.The casing is made of stainless steel for maximum strength and durability. The small dimensions of this preamplifier ensure reliable operation under humid conditions owing to the heat generated by internal power dissipation. A 1/2" version is available (G.R.A.S. 26AJ).
G.R.A.S- 26AL can handle both single and dual-sided power supplies. The supply can vary between 28 VDC and 120 VDC single-sided or ±14VDC and±60 VDC dual-sided. When using the high supply voltage (120VDCor ±60VDC), the dynamic range exceeds 140 dB.
The electrical circuit in G.R.A.S. 26AL is built on a ceramic substrate using selected low-noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone capsule’s thermal noise.
The low-frequency cut-off of the G.R.A.S. 26AL preamplifier is mainly determined by the input impedance of the preamplifier and the capacitance of the microphone capsule. The capacities 20 pF, 6.5 pF and 3 pF equal the typical capacitances of ½", ¼" and 1/8" microphone capsules respectively.
The high-frequency cut-off is determined by the preamplifier’s ability to drive capacitive loads (slewrate), caused by the cable. For large-signals, the effects of these parameters must be accounted for when measurements are performed. The large-signal response for Type 26AL for various capacitive loads corresponding to different cable lengths is shown in the data sheet. The output level is in decibels relative to 1 Volt. Typical capacitance for the cable is 100pF/m(30pF/foot).
Preamplifier G.R.A.S. 26AL (Fig. 1) is provided with a3-m light weight cable terminating in a 7-pin LEMOseries 1B plug. The cable is only 2.5 mm in diameter and will withstand temperatures from-40 oC to +150 oC. An adapter (GR0010) for G.R.A.S. 1/2" microphones is included.
7-pin LEMO plug 1B male (ext. view)
|Frequency range (±0.2 dB) with 18 pF microphone dummy||Hz||2.5 to 200 k|
|Input impedance||GΩ // pF||20 // 0.4|
|Output Voltage Swing, max. @ ±14V/+28V power supply||Vp||12|
|Output Voltage Swing, max. @ ±60V/+120V power supply||Vp||50|
|Noise (A-Weighted) max.||µV||2.5|
|Noise (A-Weighted) typ.||µV||1.8|
|Noise (Linear 20 Hz – 20 kHz) max.||µV||6|
|Noise (Linear 20 Hz – 20 kHz) typ.||µV||3.5|
|High-pass filter @3dB cut-off||Hz||TBD|
|Power supply, single||V||28 to 120|
|Power supply, balanced||V||±14 to ±60|
|DC-offset, min., single suppy||V||0.5 x Vs - 1|
|DC-offset, max., single suppy||V||0.5 x Vs + 4|
|DC-offset, balanced supply||V||-1 to 4|
|Temperature range, operation||°C / °F||-30 to 70 / -22 to 158|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Humidity range non condensing||% RH||0 to 95|
|Connector type||7-pin LEMO (FGG.1B.307)|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||8.0 / 0.28|
Conditions: 23 °C Ambient temperature, ±60V/+120V power supply, 18 pF dummy microphone, 3 m output cable.
Typical low-frequency response of Type 26AL for ½(20 pF), ¼″ (6.5 pF) and ⅛″ (3 pF) microphones
Typical max. rms output signal with 120 V and 30 V supply
Adapter for 1/4" preamplifier and 1/2" microphone
3 m LEMO 7-pin - LEMO 7-pin Cable
Customized Length LEMO 7-pin - LEMO 7-pin Cable
1/4" Microphone Holder, POM
1/4" Microphone Holder, Stainless Steel
Adapter for 1/8" microphone and 1/4" preamplifier
Right-angled (90º) Adapter for 1/4" Microphone and 1/4" Preamplifier
6pF Preamplifier-input adapter for 1/4" microphones
2-Channel Power Module with gain, filters and SysCheck generator
2-Channel Universal Power Module with signal conditioning and PC interface