All G.R.A.S. microphone preampliﬁers are based on a small ceramic thick-ﬁlm substrate with a very high input impedance. The ceramic substrate is shielded by a guard ring to minimise the inﬂuence of stray capacitance and microphonic interference. The casing is made of stainless steel for maximum strength and durability. The small dimensions of this preampliﬁer ensure reliable operation under humid conditions owing to the heat generated by internal power dissipation.
26AA can handle both single and dual-sided power supplies. The supply can vary between 28 VDC and 120 VDC single-sided or ±14 VDC and ±60 VDC dual-sided. When using the high supply voltage (120 VDC or ±60 VDC), the dynamic range exceeds 140 dB.
The electrical circuit in 26AA is built on a ceramic substrate using selected low-noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone capsule’s thermal noise.
The low-frequency cut-off of the 26AA preampliﬁer is mainly determined by the input impedance of the preampliﬁer and the capacitance of the microphone capsule. The capacities 20 pF, 6.5 pF and 3 pF equal the typical capacitances of ½″, ¼″ and ⅛″ microphone capsules respectively. The high-frequency cut-off is determined by the preampliﬁer’s ability to drive capacitive loads (slew rate), caused by the cable. For large-signals, the effects of these parameters must be accounted for when measurements are performed. The output level is in decibels relative to 1 Volt. Typical capacitance for the cable is 100pF/m (30pF/foot).
G.R.A.S. 26AA Preampliﬁer is supplied with 30 cm cable terminating in a 4-pin LEMO plug. It is for use with the G.R.A.S Intensity Probe 50 AI. An extension cable, AA0007, is available with a 4-pin LEMO connector at one end and a 7-pin LEMO series 1B plug at the other end.
|Frequency response (±0.2 dB) with 18 pF microphone dummy and 4.7 nF cable load||Hz||2.5 to 200 k|
|Output Voltage Swing, max. @ ±14V/+28V power supply||Vp||10|
|Output Voltage Swing, max. @ ±60V/+120V power supply||Vp||50|
|Noise (A-Weighted) maximum||µV||2.5|
|Noise (A-Weighted) typical||µV||1.8|
|Noise (Linear 20 Hz – 20 kHz) maximum||µV||6|
|Noise (Linear 20 Hz – 20 kHz) typical||µV||3.5|
|Power supply, single||V||28 to 120|
|Power supply, balanced||V||+-14 to +-60|
|DC-offset, minimum, single suppy||V||0.5 x Vs - 1|
|DC-offset, maximum, single suppy||V||0.5 x Vs + 4|
|Temperature range, operation||°C / °F||-30 to 70 / -22 to 158|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Humidity range non condensing||% RH||0 to 95|
|Humidity coefficient @250 Hz||dB/% RH||TBD|
|Connector type||7-pin LEMO (FGG.1B.307)|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||22.00 / 0.78|
|Weight with cable and connector||g / oz||TBD / TBD|