Typical applications and use
Electroacoustic tests of:
- Hearing aids
- Portable devices, for example tablets, GPS, etc.
It is designed for automated production line testing of key loudspeaker parameters, such as frequency response, rub and buzz, THD, and impedance. The 12AU’s design makes it ideally suited for test of portable devices with built-in loudspeaker such as mobile phones, hearing aids, tablets, and GPSdevices.
The inherent noise is very low, and by design it avoids system-generated noise, for example from ground loops. In a measurement setup, it controls the paths of (a) the signal sent out to the loudspeaker and (b) the resulting acoustic signal picked up by a condenser microphone fitted to the preamplifier.
It is remotely controlled via its USB interface and, for this purpose, is delivered with a control program for Microsoft Windows ®.
- Single channel conditioning amplifier suited forboth CCP and 200 V LEMO preamplifiers
- Very low inherent noise
- The speaker input and the analogue outputs are floating with respect to common ground to avoid system-generated noise
- Speaker amplifier with measurement of loudspeaker impedance without disturbing the speaker
- Fulfils EMC requirements according to EU regulations
- Full remote control via USB interface
- Gain settings:
– Microphone conditioner: 0 to 50 dB in 10 dBsteps
– Speaker amplifier: –20 dB to +10 dB in 10 dB steps
– Current output: 0 dB and +20 dB
– Microphone amplifier: 1 Hz or 20 Hz
– Speaker amplifier: DC or AC coupling (10 Hz)
- Comprehensive status and overload indication
- Rack mountable in 19” rack.
Measurement Control with 12AU
In a complex measurement setup, it is often difficult to avoid system generated noise. Also, it can be tedious to correctly set up all the parameters of the measurement chain with respect to sensitivity, gain, filtering and overload handling.
With the 12AU, you can control the loudspeaker amplifier and microphone conditioner simultaneously.
The 12AU is remote-controlled via its USB interface and a control program for Windows. You can operate the 12AU using a graphical user interface or by entering commands. Multiple 12AUs can be controlled from the same PC.
These features make the 12AU ideal for automated production line testing.
All outputs except the speaker amplifier output have fixed 100 kHz (3 dB) low pass filters to minimize the need for anti-aliasing filtering in the following analyzing equipment. There is no phase shift between microphone input and output due to prepolarized or externally polarized microphones. It is designed without relays.
|Frequency range (±3 dB)||Hz||1 - 100 k|
|Inherent noise, LIN (20 Hz to 20 kHz) re input, when not dominated by output||µVrms||1.5|
|Inherent noise, LIN with dummy micophone (20 Hz to 20 kHz),||µVrms||< 5|
|Gain settings, 10 dB steps||dB||0 to + 50|
|Gain error||dB||< 0.2|
|High-pass filter||3-pole Butterworth, -1 dB @ 20 Hz|
|Type||Constant Current Power (CCP) and Traditional power supply (LEMO)|
|Input channel, CCP||1|
|Input channel(s), traditional power supply||1|
|CCP preamplifier supply @ +28 V||mA||4|
|Polarization voltage||V||0 / 200|
|Loudspeaker output (4 pin LEMO)||Yes|
|Power amplifier input impedance||Ω||10 k|
|Power amplifer output connector||2-pin LEMO|
|Power amplifier output current||Ap||1,4|
|Power amplifier gain settings, 10 dB steps||dB||-20 to 10|
|Power supply, external (±10 %)||Vac||110 to 240|
|Power amplifier frequency range||Hz||DC to 30 k|
|Power amplifier phase shift response (±1 deg)||Hz||DC to 80 k|
|Power amplifier output voltage||Vp||14|
|Power amplifier overload detection||Yes|
|Power amplifier output current monitor connector||BNC|
|Monitor output connector||BNC|
|Monitor output impedance||Ω||100|
|Weight||g / oz||2500.00 / 88.18|